How To Install Corrugated Roofing On A Shed

Download Article

Download Article

Corrugated roofing is a great way to height a garden shed, shop, or patio. It's quick, easy, low cost, and you can practise it yourself. You lot but need some basic tools and materials.

1. 1

   Cutting the panels to the desired length. Most panels come to 32 feet (ix.eight one thousand) in length. Allow for a minimum of eighteen inches (46 cm) if y'all need to lap to complete the run.

   Cutting tools:
   Angle grinder: ^[1] The fastest option. Wear hearing and eye protection. Paint or prime cut edges to forbid rust.
   Circular saw: ^[ii] Slower than angle grinder, but follow same instructions. Use a metal blade and look information technology to wear quickly.
   Nibbler: Effective if rated for the right metal and guess.
   Tin snips: ^[3] Deadening but safe. Clothing work gloves and find the longest pair you can.

2. 2

   Pre-drill holes on the ridges. Some panels have pre-drilled holes. If yours do non, then you lot will need to drill holes in them. Use a ⁱⁱⁱ⁄_sixteen  in (iv.8 mm) drill scrap.^[4]

   • Spacing for the holes on the ends and sides of the panels should be 6 to 8 inches (15 to 20 cm).

   Advertisement

3. iii

   Install the panels. Place them directly onto purlins that are attached to the roof trusses, beginning on the exterior edge.^[5]

   • Close or seal off the ends with a wood or plastic strip under the panel at each cease. These volition stop the entry of rain, wind, and pests.

4. 4

   Screw downwardly the panels. Pre-drill the holes, and apply x by two in (25.4 by v.1 cm) screws with polycarbonate washers.^[6]

   • Continue across the roof until it is completely covered, lapping over the previous console by at least 2.5 inches (vi.4 cm) minimum.
   • Suit the lap so that the last console completes the coverage without making a cutting lengthwise.

5. 5

   Complete the opposite side. If your roof is two-sided (and non merely a unmarried slope), repeat the installation on the other side of the roof, and install a corrugated ridge cap as you proceed across with the panels.

   Advertizing

1. 1

   Choose the type of corrugated roofing yous want to apply: PVC/fiberglass, or metal.^[seven] These come in diverse lengths, but with a nominal 26 in (66 cm) width.^[viii] They each have advantages and disadvantages.

2. 2

   Choose PVC covering to let light in. The reward of the PVC/polycarbonate roofing is the translucency of the panels. They allow daylight to enter through them.

   • If cost is a gene, PVC is a cheaper alternative to sheet metal.
   • PVC will block out the heat from the dominicus much more effectively than sheet metal, which will human action like a radiator.
   • Some PVC is translucent, merely filters ultraviolet rays, and comes in a multifariousness of colors.
   • The disadvantages of PVC are that it's not equally durable as canvass metal, is noisy in the pelting, and can hands pause off during loftier winds.

3. three

   Selection metal covering for greater immovability. One of the strongest features of corrugated metal is its durability. Mod galvanized steel or aluminum is resistant to rust, and tin easily last up to 100 years. Metallic panels are much more durable than asphalt shingles, and then you lot won't need to repair or supercede your roof equally ofttimes.^[9]

   • A corrugated metal roof is quieter than PVC when it rains.
   • Metal roofing resists rot, is not susceptible to insect damage, and is non-combustible (a boon in fire-prone areas).
   • One downside is that the metal sheets take a susceptibility to denting, both in installation and during hailstorms. Metal roofing can too exist significantly more than expensive than PVC.

   Advertizing

Inquire a Question

200 characters left

Include your electronic mail address to get a message when this question is answered.

Submit

Advertisement

Video

• Lay the panels on the footing the way yous desire them to be on the roof. This helps in setting up the lap of the panels.

• Install a corrugated roofing wall connector panel to a wall with roofing sealant when installing panels for a patio embrace. Follow manufacturer's instructions for the sealant awarding.

• When framing the roof, the spacing for roof trusses should not exceed 24 inches (61 cm) and purlins should not exceed 36 inches (91 cm) apart.

• Yous tin use both types of corrugated roofing together, creating panels that will allow light to come through as with a clear or white fiberglass corrugated panel known as a skylight.

• One of the large advantages of metal roofs is their energy efficiency. A properly installed corrugated metal roof will help prevent oestrus flow into and out of a building, so you won't need to use equally much energy controlling the temperature inside.^[ten]

Advertizement

• Work from the sides, using ladders or movable scaffolding, to avoid standing or walking on the panels.

• Do non drill holes for the screws in the valley of the ridges to prevent leaks.

• Before you lot install corrugated roofing on your domicile, check local building codes to find out if in that location are any restrictions on using this kind of roofing.

Ad

Things You'll Need

• Corded or cordless electric drill
• Straight border
• ³⁄₁₆  in (4.8 mm) drill bit
• Circular saw or jigsaw with metal cutting blade
• Tin or heavy-duty garden snips
• Polycarbonate or galvanized metal corrugated roofing panels
• 1 by 3 purlin material
• Cease stops
• Corrugated wall connectors
• Corrugated ridge connectors
• 10 by two in (25.four past 5.one cm) corrugated fasteners with polycarbonate washers
• Self-tapers
• Covering sealant (just if manufacturer of corrugated polycarbonate recommends using)

About This Commodity

Commodity Summary X

To install corrugated roofing, showtime by cutting your panels to length with an angle grinder. Next, pre-drill holes on the end and side ridges of the panels, spacing the holes half dozen to viii inches apart. Beginning at the outside edge of your roof, place each panel directly onto the purlins that are attached to the roof trusses. Screw downwards the panels using the pre-drilled holes, then go on beyond the roof until information technology is completely covered. To acquire more from our Contractor co-author, similar how to choose betwixt corrugated PVC or metal covering, keep reading the article!

Did this summary assistance you?

Thank you to all authors for creating a folio that has been read one,008,081 times.

Did this article assist yous?

Source: https://www.wikihow.com/Install-Corrugated-Roofing

Posted by: whitttiver1990.blogspot.com

Share this post